To reset a tripped breaker, open your electrical panel, find the switch sitting in the middle or OFF position, push it firmly all the way to OFF, then back to ON. To reset a GFCI outlet, press its RESET button until it clicks. If a dead outlet has no buttons, check the nearest GFCI in a bathroom, kitchen, garage, basement or outside. If it trips again right away, unplug everything on that circuit and call a licensed electrician.
Every winter I hear the same story. Someone is running a space heater, a hair dryer and the coffee maker at the same time, the bathroom goes dark, and they are standing there in a towel wondering if the house is haunted.
The house is not haunted. The house is doing its job. A tripped breaker or GFCI is a safety device shutting things off before something gets hot, melts, or shocks you. Annoying, yes. Also kind of heroic. Panic is optional.
Here's how to figure out which one tripped, how to reset it properly, and when it's time to stop flipping switches and call a pro.
What's the difference between a breaker and a GFCI?
A circuit breaker lives in your electrical panel and protects the wiring in your walls. It trips when a circuit pulls more current than the wire can safely carry, from an overload or a short circuit.
A GFCI (ground fault circuit interrupter) is usually an outlet with TEST and RESET buttons. It watches for electricity leaking somewhere it shouldn't, like through water or through you, and cuts power in a fraction of a second. That's why you find them near water: bathrooms, kitchens, garages, laundry areas, unfinished basements and outdoors.
Some houses also have GFCI or AFCI breakers in the panel itself. Those look like regular breakers with a small TEST button on them. They reset the same way as any other breaker.
How do I know if it's a breaker or a GFCI?
Look at what went dead. One outlet or a small group near water usually means a GFCI. A whole room or several rooms usually means a breaker.
| What you notice | Most likely cause | Check first |
|---|---|---|
| One outlet or a few near a sink are dead | Tripped GFCI | Press RESET on the nearest GFCI |
| A dead outlet with no buttons on it | A GFCI somewhere else on the same circuit | Every GFCI in bathrooms, kitchen, garage, basement and outside |
| A whole room or several rooms are out | Tripped breaker | Your electrical panel |
| The whole house is dark and so are the neighbors | Utility outage | Your utility's outage line |
| The whole house is dark but the neighbors have power | Main breaker or service problem | The main breaker, then your utility or an electrician |
If the whole street is dark, this guide is not your guide. Head to what to do when the power goes out instead.
How do you reset a tripped breaker?
Push the tripped breaker firmly to OFF, then back to ON. Here's the full version:
- Turn off or unplug what was running. If the space heater caused it, the space heater will cause it again.
- Go to the panel. It's usually in the basement, garage or a utility closet. Stand on a dry floor with dry hands.
- Find the tripped breaker. Its handle sits in the middle or OFF position and doesn't line up with its neighbors. Some breakers show a small orange or red flag when tripped.
- Push it all the way to OFF first. You should feel a click. This is the step everyone skips, and it's why people tell me the breaker "won't reset."
- Push it back to ON. Then plug things back in one at a time.
Reset a breaker once. If it trips again immediately, or the panel smells like burning, buzzes, feels hot, or shows scorch marks, leave it off and call a licensed electrician. Never take the panel cover off, never tape a breaker on, and never swap in a bigger breaker to make the tripping stop.
How do you reset a GFCI outlet?
Press the RESET button firmly until it clicks and stays in. If it won't stay in, the outlet probably has no power coming to it.
- Unplug anything connected to that outlet.
- Press RESET firmly. If it has an indicator light, the light should change.
- If RESET won't stay in, check the panel for a tripped breaker first. Most GFCIs can't reset without power.
- Plug in a lamp, press TEST, and the lamp should go off. Press RESET and it should come back on. That tells you the GFCI is working.
- Plug your things back in, one at a time.
Why is my outlet dead when there's no GFCI next to it?
One GFCI can protect several regular outlets "downstream" of it on the same circuit. When it trips, all of them go dead, even ones in a different room.
I have seen a GFCI in the garage controlling the outlet on the back patio, and one in the main bathroom controlling the outlet in the hall bath. Builders are not always thinking about you at 7 a.m. with wet hair. I say that with love, as a builder.
So check every GFCI: each bathroom, the kitchen, the garage, the basement and outdoors. Look for a small "GFCI Protected" sticker on the dead outlet, which is a clue it's fed from somewhere else. And check the panel for a GFCI breaker with a TEST button.
Why does my breaker or GFCI keep tripping?
Repeated tripping is a message, not a malfunction. The usual causes:
- Too much on one circuit. Space heaters, hair dryers, microwaves and window air conditioners pull a lot. Move one of them to a different circuit.
- A bad appliance. If it trips the moment you plug in one thing, try that thing on a different GFCI. If that one trips too, the appliance is the problem.
- Moisture. Outdoor and garage GFCIs often trip after rain. Let it dry out, and make sure outdoor outlets have a weatherproof cover.
- A worn-out GFCI. They don't last forever, often around 10 to 15 years. One that trips constantly or won't reset may simply be done.
- A wiring problem. If it trips with nothing plugged in, or trips the instant you reset it, there may be a short or ground fault in the wiring. That's an electrician's job.
When should you call an electrician?
Call a licensed electrician if any of these happen:
- A breaker trips again right after you reset it.
- A breaker or GFCI trips with nothing plugged in.
- You smell burning, hear buzzing, or see scorch marks on an outlet or the panel.
- An outlet, switch or the panel feels warm.
- A GFCI won't reset even though the breaker is on.
- The same circuit trips over and over during normal use.
Anything inside the panel, and replacing outlets or adding circuits, belongs to a licensed electrician. Here in Bucks County, panel work and new circuits usually need a permit through your township, and a good electrician handles that for you.
How often should you test GFCI outlets?
Test them once a month. Press TEST, confirm the power goes off, then press RESET. A GFCI that doesn't cut power when you press TEST isn't protecting anyone and should be replaced by an electrician.
The easy way to remember: test them the same day you test your smoke alarms. If you need a refresher on those, here's where smoke and CO detectors go and when to replace them.
Label your panel while nothing is wrong
The worst time to learn your panel is in the dark with a flashlight in your teeth. Pick a quiet Saturday, flip breakers one at a time, and write down what each one controls. It takes an hour and saves you a lot of guessing later.
Snap a photo of the labeled panel and keep it with the rest of your home records. Future you, standing in a towel, will be grateful.
Common questions
Why won't my breaker reset?
Most breakers have to be pushed all the way to OFF before they will go back to ON. If it still won't stay on, or trips immediately, there may be an overload or wiring fault, so leave it off and call a licensed electrician.
Why is my GFCI outlet not resetting?
A GFCI usually can't reset without power, so check your panel for a tripped breaker first. If the breaker is on and the GFCI still won't reset, the outlet may be worn out or there may be a wiring problem that needs an electrician.
Is it safe to keep resetting a breaker that keeps tripping?
No. Resetting once is fine, but a breaker that keeps tripping is warning you about an overload, a bad appliance or a wiring problem. Find the cause, and call a licensed electrician if it trips with nothing plugged in or right after a reset.